MUSICONICA
Pages: [1]
  Print  
Author Topic: Missing Inboard Pad Retaining Spring...Left Rear, '87  (Read 8619 times)
0 Members and 1 Guest are viewing this topic.
Warlordsix
Newbie
*
Offline Offline

Posts: 20


Topic starter

« on: May 13, 2016, 09:54:29 PM »

Hi guys.
Well tonight I tracked down the nagging rattle I had when driving over bumps.  The inboard pad on my left rear caliper was loose and fell out when I removed the caliper off the rotor.  Upon inspection I noticed the retaining spring/clip that fits around the piston was missing.  Explains the rattle AND the shitty brake feel I was also trying to track down.  So the question...is that spring available separately or do I need to buy a whole caliper to get one.  I'll check at the parts stores in the morning, but I'm not holding my breath.
Thanks.
Ernie
Logged

'87 Fiero 4.9 V8 5-speed, two Rokon 2-wheel drive bikes and an ATK 406XC hare scrambles bike...yeah, I'm a nutcase for weird, American iron.
Pappy
Global Moderator
Official CFF Post Whore
*****
Offline Offline

Gender: Male
Posts: 1787


1988 Formula SII-SC 3800 M17 - The Maroon Menace


« Reply #1 on: May 14, 2016, 07:26:37 AM »

Ernie,
Here's something to think about

A lot of stock Fiero parts are interchangeable with other vehicles
http://www.fierosails.com/PartsManual.html

I don't know if your car has stock brakes but I'm guessing they have been upgraded
HOWEVER with that said, no telling what is actually on your car without looking at it and I'm sure one of us can figure it out - Maybe the PO could answer the question

Oh the joys of "Fiero Life"  wink



« Last Edit: May 14, 2016, 07:34:48 AM by Pappy » Logged

Pappy - Crusty old retired MSgt
To Err is Human, to Forgive is not SAC Policy
Warlordsix
Newbie
*
Offline Offline

Posts: 20


Topic starter

« Reply #2 on: May 14, 2016, 07:55:15 AM »

Thanks, Pappy.  Yeah, the calipers are stock, pads brand new as are the rotors, which are slotted and drilled.  PO did good work, but that clip is missing.  Last night I searched online and found a so-called "Brake Hardware Kit" thru OReillys, Autozone and Advance Auto Parts, that includes the clip.  Cheap enough at $14, but whether they have it in stock is another matter.  I want to get this together and do some driving this weekend!

Thanks, again.

Ernie
Logged

'87 Fiero 4.9 V8 5-speed, two Rokon 2-wheel drive bikes and an ATK 406XC hare scrambles bike...yeah, I'm a nutcase for weird, American iron.
uhlanstan
Veteran Member
Sr. Member
*****
Offline Offline

Gender: Male
Posts: 844


Carefree derelict, seeks buxom blue eye blond with


« Reply #3 on: May 21, 2016, 10:20:33 PM »

 I probably have this clip if you can not find
Logged

why belong to a club that had me as a member ?
Warlordsix
Newbie
*
Offline Offline

Posts: 20


Topic starter

« Reply #4 on: May 22, 2016, 10:24:00 PM »

Many thanks, Uhlanstan, but the Brake Hardware Kit contained two retaining clips, one for each rear caliper.  The front pads don't need them, as they mount differently.  In any case, it turns out the clips were missing from BOTH of my rear calipers.  Not anymore.  Clips are now on, and the inboard pads are now held properly.

Ernie
Logged

'87 Fiero 4.9 V8 5-speed, two Rokon 2-wheel drive bikes and an ATK 406XC hare scrambles bike...yeah, I'm a nutcase for weird, American iron.
Pages: [1]
  Print  
 
Jump to:  

Go to CFF Club & Vendor links.